I went back to my first module and started wiring…probably something that I should have done before the scenery.

I have all of my machinery parked on the module, they are all from Rio Grande Models.

More wires in front of the ice house…and a new sign for the ice house.  I used the Model Builder software to modify it from the gif file I found.  I used white glue to attach it to the building.

]]> http://www.railroadredux.com/2012/01/begining-wiring-after-the-scenery-is-mostly-in-place/feed/ 1 http://www.railroadredux.com/2012/01/rock-castings-waterfalls-and-trestle/ http://www.railroadredux.com/2012/01/rock-castings-waterfalls-and-trestle/#comments Mon, 23 Jan 2012 15:41:49 +0000 Dom http://www.railroadredux.com/?p=653

Here is a picture of one of my tunnel portals in place and one of the rock castings from Bragdon ent.  This will be the only place where I used the entire casting in one piece, I will break different pieces off and reassemble them for the other rock faces.

Here is more of the rock casting used in pieces to create one side of the canyon.  The bottom of the river is in place and partially painted. (note to self – should have used flex paste to fill holes before installing gravel).

Here is a view higher up the canyon, showing where I have started to use Woodland Scenics water effects to create the rapids and small falls.

A final view shows the beginnings of my trestle, which I am custom making each one at my desk before installing it on the layout.

Here is a picture of the tree making machine I have been using for a little while.  While a very simple machine it has the ability to create very realistic model trees with moderate effort and little cost.

Here is a picture of the armatures ready for painting:

The next step will be hanging them upside down and painting brown.  After that I will use hairspray and sprinkle on ground foam.

I have spent the last couple of days working on trees.  I borrowed a tree making machine and have started making armatures for evergreen type trees.  The machine helps in making the bottle brush type of trees.  It helps by twisting a pair of wires around fibers cut from hemp rope.  After twisting the wire the armatures get cut into tree shapes.  So far I have only rough cut one tree, but the results are stunning even before painting and flocking.  I intend to purchase one of these machines as soon as I can.  Until then I will twist as many as I can.  Half will be for my home layout, the Get Out and Push railroad, and the other half will be for the San Leandro Historical Railway Society.

I went down to the San Leandro Historical Railway Society last night for our normal Tuesday open hours.  I took the storage box I spent the last couple of days down with me.  Luckily, it fit in a decent location under the layout.  I have only three drawers in so far, but it looks like it will contain my entire collection with room to spare.

I also took the second building for the Del Monte plant for the San Leandro portion of the layout.  I had added roof details and completed some of the final details over the last couple of days.  The I still need to add the interior office and warehouse details and lighting.

I spent the rest of the evening test running my new Athearn Genesis GP-9.  It pulled a decent mixed freight train through the layout, but eventually skidded out when attempting to go up the helix at a 2% grade and a fairly sharp corner.  Overall I am very pleased with the operation and sound of this model.

I need to purchase the material to complete the shelves for my storage box.

Today I spent some time terra-forming, fancy speak for making more plaster rocks using the various molds I have accumulated.  I am beginning to realize how many pieces it will take to complete this section of the layout, and it is quite a lot.  My preference is to model the scenery of the Pacific Northwest down into Northern California.  Along the coast it can be quite steep.  I am also creating a waterfall scene that winds down the mountain, so will need even more rock.  So far I have several rubber molds from Woodland Scenics, which work pretty well, and a silicone mold from Bragdon.  The silicone mold creates incredible detail, which on the other hand makes it a much more delicate job to remove the casting from the mold.  I think that I have only created one complete cast using the mold.  For all of the rest I poured thinner pieces which I broke to fit the scene.  This technique works pretty well to allow you to re-use a rock mold many times over.

I found out the hard way that it is extremely important to seal the area completely when using the Woodland Scenics realistic water.  It found many small holes and drained out after a period of time.  I still haven’t figured out how I will seal the pond areas before filling them.  I am thinking that I can use the Woodland Scenics water effects as a sealing coat before adding more realistic water.  I will post the results when I do figure it out.

During a recent trip to Spartanburg, SC I viseted the Hub City Railroad Museum.  While there I had the opportunity to see two different trains from two different companies at the same time.

This first picture was a CSX coal drag on one side of the depot which the museum is located in.  The train is running on the left leg of the wye, with a switch to the left of this photograph and another leg running right below.

A view of the patched out cars, you can see the lower leg of the wye in the foreground.

One of the museum docents and some of her friends watching the rear helper come into view.

The rear helper being photograhed by another docent from the museum.

While the CSX coal drag was passing slowly on one side of the depot a Norfolk Southern auto and intermodal train pass quickly on the other side.

The motive power.

A view between the NS mainline on the right (just out of the picture) and the CSX on the left.  This is the other two legs of the wye that the coal drag was running along in the previous pictures.  An abandoned rail bridge is in the left of this picture, covered in kudzu.  Also of interest was that directly behind me in this shot the CSX ducks into a tunnel (unfortunately did not get a pic) which crosses under the NS mainline.

After seeing the number of different lines that come together in this particular spot, it is easy to understand why they call Spartanburg the hub city of the South.

I went down to the San Leandro Historical Railway Society last night for our normal Tuesday open hours.  I was able to run my new Genesis GP9 after I set it up using Decoder Pro (much easier to set all the variables and I still don’t have it set up at home).  I pulled two reefers and a caboose around the entire layout and switched in Colfax.  Overall it ran really well, no major hiccups other than the caboose kept derailing (need to check the weight I think).

Overall an excellent model for the price.

I hope that everyone had a good Christmas, I certainly did. The major gift that I received from my wife was a table saw.  She got it at a really good price through Lowes, it is a Skil 15amp with a 10″ blade.  It has a stand to bring it up to the correct height.   One of the best things about it is that it stores all of the guards and accessories under the main table so they don’t get lost.  Thanks also to my father in law for the help in picking it out.

I also received a small rechargeable drill, which will come in handy when I start on the scenery and need to drill a bunch of small holes.

Today I purchased a new locomotive, an Athearn Genesis Gp9 with the Tsunami sound in the Southern Pacific with the Black Widow paint scheme.  It will be nice to have a diesel with a sound decoder, and even better is to have a road switcher than I can use during the ops sessions (correct horn signals, etc.).

Work on the Get Out and Push RR has been continuing, albeit at a snails pace.  I am working on creating the landforms for the site of my waterfall.  I am finding that it is taking a large number of rock castings and batches of plaster to create the desired effect.  I am also in the process of building the trestle that will support my reversing loop.

As usual I am in the middle of a couple of different projects at the same time. Currently I am working on a Campbell model, Bret’s Brewery.  This kit has been a pleasure to build and is nearing completion with all of the major components assembled with the exception of the roofs.  I tried an interesting technique for creating the mortar lines on model stone.  I watered down a couple of drops of grey paint and used a large brush to apply it to one side of the building at a time.  Leaving this side up, I placed it in front of my heater and waited until it had dried.  Gravity held the paint into lines and using the heater allowed me to quickly paint all three sides.  In hindsight I probably should have painted them before assembling the walls, but I still would have had an issue on the corner joints.  The technique worked quite well.

The other major project I am working on is a freelanced building for the San Leandro Historical Railway Society .  It is the second building that I am using to represent the Del Monte fruit packing plant which used to be in San Leandro.  It will be placed across the tracks from the first building, connected by a bridge for pipes and electrical wires.  These structures will help to hide a spot where the tracks disappear through a hole in the backdrop.  Test fits of the building show that this will work very well.  I have the structure assembled, with the doors and windows in place.  I am currently working on painting the structure, I need a little touch-up and the exterior will be done.  The next step will be to paint the interior and install desks and people to represent an office scene.

I hope to post pictures soon.

Merry Christmas