After reviewing some of my previous posts, I realized that I hadn’t put up the final pictures of this fine model.  So, without further ado, here they are:

(I just had to say that, lol)

Here is a picture of the rear of the house, showing off the back porch.

And here is a view of the right side of the house.  You can see the seams on each end of this wall.  This is so I can remove this wall with little damage to the building if I ever decide to put an interior into it.  When I place it on a layout I will cover this seam with ivy.  I will also lightly weather the house after it is in place to fit the location.

I constructed the front porch using the same techniques as I did on the back, building a wood frame under the floor and using it as a mounting point for the lattice.  I didn’t bother installing legs on this one either, however it would have helped in the installation by keeping the back corner of the porch up while waiting for the glue to set.

I painted directly over the cardstock for the porch floor and continued with the assembly of the porch.  When installing the gingerbread I found that it was much easier when using a curved pair of tweezers to hold them.  I used the same technique as before on the gravel for the roof, painting the surface with roof brown, followed by a coat of scenic cement, and then sprinkling on the ballast.  I then used a pipette to add cement where needed.  I found in a couple of spots the ballest ended up getting stuck on the walls higher than I wanted.  The best solution for this was to use an x-acto knife to push these spots down before the glue dried.

I assembled the back porch following the directions.  The cut out piece seemed to fit a little bit strange so I had to do some cutting to get it to fit correctly.  I used Elmer’s wood glue to hold the pieces together.  In the foreground of the picture you can see how I framed the porch with scale lumber, and after it had dried I used the pieces of lattice to build up the rest of the porch.  I didn’t bother installing any posts going down as you can’t see them anyways.

I then painted the porch and installed all of the “gingerbread around the edges of the roof.  The roof was painted with Floquil’s roof brown and then covered with fine ballast to provide texture.  Using the ballast is a good way to cover the small cuts and adjustments that were needed on the roof.  Also in this picture you can see where I added the “spears into the gingerbread around the roof of the model.  I had to use putty around some of them to fill in the gaps, but it was easy to hide the patches.

For this section of the build I installed the chimneys first, after assembling them.  I painted them by dry-brushing a couple of colors over the gray primer coat.  I used a ca glue to assemble them and to fix them to the wall.  I then cut each of the pieces of the parapet into the correct length, and then held it up to its final location to judge the angle I needed to cut it at.  As you can see in the picture there was a slight gap between each one, but I was able to use Squadron white putty to cover those.  You can’t see it from the picture but I made sure to paint each of the pieces before installing them, as it would have been difficult with them already in place.

After the glue had dried (it took only a couple of minutes) I began the installation of the special molding on both the parapet and the top section of the mansard roof.  At each of the major corners I left a gap for the “spike” that would go into place.  In this picture you can also see that I began to fill in the top of the bay window with putty.

After the glue had dried on the roof paper I removed the tape and began by touching up all of the roof.  I then dry-brushed several layers of color on the roof panels.  I used two colors of green and then used a dark gray and a light gray which I also used on the gravel portion of the roof.

I then began to cut the various pieces of the roof to the neccesary shape, using hobby cutters to cut them slightly over sized.  I then used a hobby knife and files to fit them in the needed spots.  I used them to cover the edges of the roof panels.  I dry-brushed the colors of the chimney to represent stone.  I intend to paint the trim later.