In previous posts I have talked about using a cork board when building certain model parts, especially docks and things of that nature.  I decided that I should share some of the things that I have learned in using this.

The chief advantage of using a cork board is that you can place the templates included in the model (or drawn by you as the case might be) onto the cork and cover it with a sheet of wax paper.  The section of the model can then be built right over the template without damaging it, at the same time the cork allows pins to be used to hold parts into place.

Here is a picture showing the first step in building an extension to my ice dock for the Union Ice Co. kit:

As you can see in the picture I use the pins to keep the parts in alignment until the glue has dried.  This allows me to use a slower drying glue, such as the Elmer’s Wood Glue – which gives me plenty of time to make sure that the parts are aligned to match the template.

The next step was to lay out the stringers, on which the frames will be glued.  I also added the cross bracing to one side at the same time, after allowing them time to dry I can use a hobby knife or razor blade to remove the frames from the wax paper after I have removed the pins.  The wax paper makes this relatively easy.  I then glue the cross bracing on the opposite side.

The next step is to glue the frames into place on the stringers, using pins as needed for support.

Once the part has dried I can remove the completed assembly from the cork board by removing all of the pins and then using the hobby knife as needed.  The final cross bracing and deck can then be put on.

After adding the long expanse of the ice dock on the Union Ice Company kit, I decided that I was going to extend the dock in a “T” shape to meet the building instead of just installing a ramp for the ice.  I used the template for the original ice dock to create the needed parts, though I ended up using slightly smaller material (what the hobby shop had available).

Here is a picture showing the end of the existing dock, which I added a Plastruct stairway and railings as the wood looked too “cluncky”.

I then assembled the filler piece for the dock on the cork board and inserted the completed piece into the gap, using a bottle of paint as a weight to assist in gluing the piece into place:

Here is the completed addition to the dock, waiting for the ice ramp and railings to be installed.  My logic behind making the change in the ice dock was to make it so that if a block was stuck, the workers would be able to walk over and fix the problem without needing a ladder.  Also I added a small ladder going up from that level to the shorter section of the roof, which I will show in a later post.

For the ice loading dock for the Union Ice Company kit I followed the directions for the most part.  The only change that I made was to make the bracing the same for middle uprights as the ends.  I did not like how the small supports recommended in the kit looked after building the first upright.  I used additional scale lumber from Northwest Short Line to provide the needed material.

The second picture shows how I used a cork board and pins to build the ice loading platform right on top of the instructions, which are covered by wax paper.  This technique allowed me to use the pins to secure each piece into the correct place while I was waiting for the glue to dry.

This picture shows how used bottles of paint as weight to glue the completed platform into place.

I recently purchased a very useful tool at my local hobby shop.  The Chopper II, made by Northwest Short Line, is a device for cutting scale lumber.  By using a rigid blade on a pivot it allows you to make straight cuts on scale lumber up to 1/4″.  This version has a self healing mat on the cutting surface, which should add considerable life to the tool.

By using the stops that come with it making duplicate cuts is very easy, allowing for large numbers of identical pieces to be cut quickly.

• Overall: 10
• Provided parts: 10
• Instructions: 10
• Value for price: 9
• Overall quality: 10

Here the various sub assemblies are put together on the base I cut out of scrap plywood.  In this picture you can see that I have constructed and installed the front dock and the back porch, the only major change I made was in putting another ramp on the near end of the dock.  I have yet to finish weathering the back porch.  The dock was weathered using various pastel chalks, similar to what I did on the floor of the building.

Also in this picture is the foundation which the office rests on.  For the desired effect I started with a dark gray and dry-brushed two lighter colors of gray on top.  I touched up the highlights with a final light dry-brush of white.

This picture shows the front view, a little bit further on.  Notice that I have put some of the doors in place, and the cardstock for the roof.  In hindsight it would have probably been better to build the sub roof using scale lumber, as you can see the edges of the cardstock under the corrugated metal roofing.  I set the side door part way open, with someone standing in it to add life to the building.